Ultimate Install Ultimate Install

Ultimate Install

HDB Ultimate Handguard™Install

Set Includes:

1 - HDB Top Clamp, ,

1 - Pair of HDB Ultimate Handguards,

1 - Pair of Plastic Shields,

2 - Swivel Bosses,

2 - Threaded Inserts,

1 - 5/8-11 tap,

4 - 8mm x 35mm SHCS,

2 - 8mm x 30mm BHCS and washers,

2 - 8mm x 20mm BHCS w/ washers,

2 - 8mm x 40mm FHCS,

4 - 5mm x 16mm BHCS w/ washers,

Mirrors are optional.

Note: The set does not come with a black anodized top clamp. Instead, it is a bare top clamp.

1. If you have grips on your bars, remove them and prep the ends for handguards by trimming the ends out of both sides and also the throttle tube. This needs to be done to ensure metal to metal contact of the handguards and handlebars

2. Tap the handlebar ends for threaded inserts, using a 11mm 12 point socket for the square end of the tap and WD-40 or equivalent for a lubricant, run the tap in to the end of the threads. For best results keep the centerlines of the tap and the bars aligned, turn the tap one revolution clockwise before turning at least one revolution counterclockwise to break the chip, if the taps binds, back it out and blow out the shavings and continue.

3. Use blue Loctite to glue in the inserts.

4. Install the threaded inserts so they are inside the bars by about 1/32".

5. Remove old top clamp and install HDB Top Clamp using the 4-8mm x 35mm SHCS (you might find it easier to attach the Computer Protector, Computer and Swivel Bosses before bolting the HDB Top Clamp to lower handlebar clamps).

6. Attach Swivel Bosses to Top Clamp using the 2-8mm x 30mm BHCS and washers, tighten until snug then back off 1-2 turns.

7. Attach the swivel end of the Handguards to the Swivel Bosses using the 2-8mm x 20mm BHCS and washers, tighten till snug then back off 1-2 turns.

8. Attach the bar ends of the Handguards using the 2-8mm x 40mm FHCS and tighten in desired position. In some cases, because of the different bends and raises of bars, there will be a gap that will need to be tightened up.

14. Tighten the bar end to its final position.

9. Attach Shields using the 4-5mm x 16mm BHCS and washers. For best results, get both screws started before tightening

16. Check and tighten all bolts.

Attach optional Mirrors if included using the M5 x 25mm SHCS, Nyloc nut and washer. For best results, tighten the mirrors M5 SHCS, then place the shield on the threads extending from the guards and get shields other BHCS started before tightening.

If more adjustment is desired from the mirrors it is possible to drill out the mounting hole the M5 SHCS goes through to allow more movement in the mirror to handguard joint.


Megan from HDB

Home  |  About  |  Contact
HDB Offroad Inc.
Your Cart
Your Cart: Empty
Experiencing ordering problems? Please visit our new site at: https://HDBOffroad.com/
Visa MasterCard AmericanExpress Discover PayPal
Experiencing ordering problems? Please visit our new site at: https://HDBOffroad.com/
© 2023 HDB Offroad Inc., all rights reserved worldwide.
Software: Kryptronic eCommerce, Copyright 1999-2023 Kryptronic, Inc. Exec Time: 0.065632 Seconds Memory Usage: 8.190475 Megabytes
I Understand
The cookie settings on this website are set to 'allow all cookies' to give you the very best experience. By clicking 'I Understand', you consent to 'allow all cookies'. If you want, you can change your settings at any time by visiting our cookies page. More About Cookies